Lite guide controller AE1000 - Bộ điều khiển chỉnh biên AE1000

Xuất xứ:

Japan

Tình trạng:

Mới 100%

Bảo hành:

12 tháng

Mô tả:

TMP là đại lý hãng Nireco tại Việt Nam

Chia sẻ:

Số lượng

Chi tiết sản phẩm

Web Control Systems
Edge Position Control Systems(Electric type)

Liteguide Controller AE1000

Overview

The Liteguide Controller AE1000 carries out EPC （Edge Position Control） through a combination of Photoheads （PH16B） and Ultrasonic Sensor （UH01）, CPC （Center Position Control） through a combination of Photoheads and Autowide Sensor （AWE280 etc.） and LFC （Line Follower Control） through a combination of LH19 and LH110.

Feature

Liteguide Controller AE1000 is the successor to the previously well established AE900E and AE900L controllers.
This single type can be connected to Nireco standard sensors which has been used with the AE900E or AE900L controller.
（Some sensors may need to be used with a preamp）
Can be used directly coupled with electrical actuators K12 and K61. Can also be connected to the K80 series through use of a driver.
Has 2 systems, a sensor input stage and a shift input stage, which can be switched for use.
Uses a larger LCD display than previous models with a white backlight making it both easier to see and allowing for verification of a greater amount of information.

Configuration

Specifications

Power Supply Voltage		AC100 to 240V 50/60Hz ±10%
Power Consumption		300 VA (inrush current 100 A 10 ms typical (200 V))
Power Fuse		250V AC, 3.15 A (time-lag type)
Ambient Operating Temperature		0 to 50°C
Ambient Operating Humidity		35 to 85% RH or lower (no condensation)
Vibration Resistance		3.5 mm, 1 G, 3 to 150 Hz, three-directions (1hour)
Power supply Noise		2.5 kVp-p, normal mode, common mode 50 ns, 1μs width
Usage atmosphere:		Area with no water, flammable or corrosive gases, and little dust.
Mass		Approximately 5 kg
IP Class		IP30
Input	2 Sensor systems	Voltage input Maximum ±5V（No input resistance） Current input 0-20mA (input resistance converted to 240/2kΩ)
	2 analog shift systems	Voltage input Maximum ±10V
	Centering	Proximity switch input （0-8V, 1.2kΩ input resistance）（Applies to: KL1632. 0-90P）
	Position Transmitter	Voltage input Maximum ±10V
	Photo coupler input （12V DC, 15mA）	Remote controller : Operation mode switching（auto / manual / centering） Operation keys （left / right / auto balance / reverse） System selection（EPC1 / EPC2） Locks 3 points Actuator end limit : 2 points
Output	Electrical actuator	K12 ±24V DC, 1A(maximum) or K62 ±36V DC, 2A(maximum)
	Lamp power source	4 to 12V DC, variable （maximum 1A）
	Fine tuner, Position transmitter, LH8B	±5V power source （maximum 0.1A）
	Sensors	±15V power source （+15V, 1A; -15V, 0.2A）（Note: The current capacity on the + side combined with the lamp power source in(2) is less than 1A.）
	Centering proximity switch power source	8V DC （maximum 30mA）
	2 indicator systems	Voltage output Maximum ±10V （load resistance 2kΩ or greater） Deviation output Position transmitter output
	Photo coupler output （24V DC, 40mA）	Remote controller : Operation mode state（auto / manual / centering） System state （EPC1 / EPC2） Alarms Excessive deviation End limit Actuator lock Actuator excessive load