M748 Digital indicator.
Digital indicator type M748 has been specifically designed to operate in connection to load cells or other strain-gauges transducers.
The instrument is compact, rugged, reliable, with a very good noise immunity, manufactured with first-class components and carefully assembled and tested.
The analog-to-digital conversion of the input signal is effected by a sigma-delta A/D converter, with a 16-bit internal resolution; the instrument is a ratio meter, using the transducer supply voltage as reference voltage, so compensating any error due to voltage drops along the connecting cable.
The instrument can be provided with two analog inputs, for the acquisition of the signals of two load cells or load cell groups.
The digital functions of the instrument are carried out by a CHMOS single-chip microprocessor; several options are available (see relevant list).
Instrument setup and calibration, commands and parameter settings are carried out through a polycarbonate keyboard, with 16 numeric and function keys.
The built-in stabilized and short-circuit protected power supply unit, 5 V DC 60 mA max, is suitable to energize up to six strain-gauges bridges, 350 ohms, parallel connected.
The indicator consists of a motherboard with a display board; it can be assembled in several types of metal or plastic boxes.
Display: 5 digits, LED 7 segments, 14 mms high, red; adjustable brightness
Range: internal 16 bit, engineering unit to be stated; resolution 1, 2, 5, 10; programmable decimal point
Zero and calibration: through keyboard
Accuracy: ± (0.01% of reading + 1 unit of LSD)
Sensitivity: 1 µV/LSD
Reading rate: up to 100 readings/second
Input impedance: greater than 100 Mohms
Common mode rejection: 100db
Room temperature: operating 0 ÷ 55 °C; storage -10 ÷ 70 °C
Relative humidity: max. 80%
Temperature coefficient: 4 ppm/°C on zero; 4 ppm/°C on span
Line voltage: 115 or 230 V ± 10% - 50/60 cycle, or 12 or 24 V DC
Consumption: 5 VA max
Connections: removable binding post connectors
-TA/D Zeroing of net weight, through keyboard or remote command (free contact), with selection of indication of gross or net weight
-S1-S2-S3-S4 One, two, three or four alarms for minimum or maximum load, with settable alarm value and time delay; each alarm is provided with an SPDT relay, 2 A capacity @ 110/220 V AC
-RS232 RS232C serial output, without control signals, programmable parameters
-RS485 RS485 serial output, programmable parameters
-DP Profibus DP or Profinet or Ethernet or DeviceNet output
-UA/V-UA/mA analog output, 0÷10 V or 0÷20 or 4÷20 mA, with programmable parameters
-IA2 Dual analog input
Bộ hiển thị khối lượng load cell M748 BCS - M748 Indicator BCS
- AT2E VietNam
- Baumuller VietNam
- Bircher VietNam
- BCS Italy
- Bernard Control Vietnam
- Beckhoff VietNam
- Bussmann VietNam
- CS Instrument Vietnam
- CEIA VietNam
- DECA WELD Vietnam
- Elco Holding VietNam
- Fireye Vietnam
- IBA VietNam
- Insert Deal VietNam
- Knick Vietnam
- Koganei Vietnam
- Keofitt Vietnam
- Keller - its Vietnam
- Kiepe Elektrik Vietnam
- Mark-10 Vietnam
- Matsushima VietNam
- Nireco VietNam
- Ohkura VietNam
- Pavone sistemi
- Pora Vietnam
- Red lion VietNam
- TDK Lambda
- Teclock Vietnam
- Wago Vietnam
- Wise VietNam
- Danh mục khác
- Gastron Vietnam